Research on axial and combined sealing of plastic waste
Abstract
The collection and transportation of municipal solid waste are critical initial stages of the entire waste management system. Environmental safety, economic costs, and the possibility of subsequent recycling depend on their effective organization. Separate waste collection is one of the most important ways to further process waste. Improving the design of garbage trucks designed for separate waste collection, increasing their efficiency, and reducing their cost is an urgent and important task for urban management. This article discusses methods for compacting plastic waste, including a new method that will be used in the design of garbage trucks in the near future. The combined seal provides a higher plastic waste seal factor and a lower modulus of elasticity compared to the progressive seal.
About the Authors
Nikita M. Andriukhov
MADI; Russian Engineering Academy
Russian Federation
Russian Federation
Candidate of Sciences (Technical), associate professor; Corresponding Member
Gennady V. Kustarev
Russian Engineering Academy
Russian Federation
Russian Federation
Candidate of Sciences (Technical), associate professor, Vice President
Roman G. Danilov
FSUE NAMI
Russian Federation
Russian Federation
Candidate of Sciences (Technical), Head of the Department
References
1. Machines for collecting and removing solid household waste. The device, the basics of calculation: a textbook / V.I. Balovnev, G.V. Kustarev, R.G. Danilov, N.M. Andriukhov; under the general editorship of V.I. Balovnev and G.V. Kustarev. –M.: MADI, 2022. -164 p.
2. Andriukhov, N. M. Substantiation and development of a translational-rotational action system to increase the degree of compaction of municipal solid waste and productivity of garbage trucks : dissertation for the degree of Candidate of Technical Sciences / Nikita Mikhailovich Andriukhov, 2023. – 154 p.
3. Andriukhov, N. M. Mathematical model of the process of interaction of the pushing plate of a garbage truck with the compacted medium during translational and translational-rotational compaction / N. M. Andriukhov, G. V. Kustarev, Yu. A. Portnov // Construction and road machinery. – 2023. – No. 3. – pp. 33-37.
4. Andriukhov, N. M. Constructions of garbage trucks and waste compaction systems / N. M. Andriukhov, G. V. Kustarev, R. G. Danilov // Construction and road machinery. - 2023. – No. 3. – pp. 38-44. ,
5. Kustarev, G. V. Improving the efficiency of MSW removal from urban agglomerations / G. V. Kustarev, N. M. Andriukhov // IV International Kosyginsky Forum "Problems of Engineering sciences: formation of technological sovereignty". Collection of scientific papers of the International Scientific and Technical Symposium "Modern engineering problems of key sectors of the country's economy" : Collection of scientific papers of the International Scientific and Technical Symposium "Modern Engineering problems of key sectors of the country's economy", Moscow, February 20-22, 2024. – Moscow: Federal State Budgetary Educational Institution of Higher Education "A.N. Kosygin Russian State University (Technology. Design. Art)", 2024. pp. 48-52.
6. Gulnyashkin, A.V. Requirements for a modern garbage truck / A.V. Gulnyashkin, D. A. Ivanov, P. S. Fedusenko // Solid household waste. – 2013. – № 10 (88). – Pp. 56-57.
7. Malev, A. N. Correcting the norms of the operational mileage of garbage truck tires, taking into account the specifics of its operation / A. N. Malev, E. M. Genson // Modernization and scientific research in the transport sector. – 2017. – Vol. 1. – pp. 37-40.
8. Khudyakova, N. E. "Economics" of a garbage truck, obvious and non-obvious factors / N. E. Khudyakova // Solid household waste. – 2020. – № 3(165). – Pp. 60-64.
Review
Рецензент: О.Ю. Улитич, канд. техн. наук, доц., МАДИ
Views:
4
